Welcome to EFI Extras website.
Parts and Accessories for your Engine Management Installation.
New SPARTAN 3 wideband controllers now in Stock!
MicroSquirt V3 ECU with 8' (2.4m) loom
Price: £395 + £15 postage
MicroSquirt V3 MS2 ECU with an 8' (2.4m) loom - £395
MicroSquirt Engine Management Control - with 8′ Harness it is an entry-level, fully assembled ECU capable of running a single cylinder all the way up to 8 cylinders with up to 2 fuel and 4 spark outputs
-Supports speed density, alpha-N (TPS based), or MAF based fuel and spark tables - (MAP sensor not supplied, need
ed for Speed density)
-0.66 microsecond injector pulse width resolution
-Allows blending multiple load types, including specialized mode for independent throttle bodies
-Supports a wide variety of OEM cam and crank position sensors
-Accelerator pump or model based acceleration enrichment
-Closed or open loop idle speed and boost control -On/off nitrous control
-Wankel rotary support: 2 rotor engines with separate leading and trailing spark tables
-16 x 16 fuel and spark tables
-2 step rev limiter (launch control) with no-lift shifting
-Wideband AFR target table
-Flex fuel sensor input
-Real time barometric correction (external sensor required)
-Sequential shift cut and air shifter control
MicroSquirt Transmission Control Options - MicroSquirt transmission control free firmware allows you to use MicroSquirt with 30″ Harness to control a number of electronic automatic transmissions (gearboxes). It can work standalone or integrate with one of our ECU’s over canbus.
Control applications: GM 4L60E I GM 4L80E I GM 4T40E I GM 5L40E (dev) I A341E I 41TE (dev) I Ford 4R70W I Ford E40D (dev) I Subaru W4A33 & more…
Spartan 2 with Bosch 4.9 LSU Lambda Sensor
Price: £130 + £10 postage
Spartan 3 with Bosch 4.9 LSU Lambda Sensor
Price: £185 + £10 postage
SPARTAN 2 and the all NEW SPARTAN 3 Wideband Controllers
Spartan 2 WideBand Lambda Controller and Bosch 4.9 Lambda Sensor - £130
Spartan 2 is the first Wideband Oxygen Controller to use all extended temperature components, this means Spartan 2 offers
the widest operating temperature; -40[C] to 125[C], of any Wideband Oxygen Controller on the market.
From the frozen Arctic Tundra to the baking heat of Death Valley, Spartan 2 is the Wideband
Oxygen Controller you can rely on.
For wiring info on the Spartan 2 see HERE.
The NEW Spartan 3 WideBand Lambda Controller and Bosch 4.9 Lambda Sensor - £185
CAN Bus support for the following ECUs; Megasquirt 3, Adaptronic, Link, Haltech, as well as YourDyno dyno controller are supported. More supported devices coming soon via firmware update.
2x Programmable Linear voltage outputs
Onboard FTDI based serial-USB converter.
This is the Yukon version, so its the coil with an increadable high power output. It can be directly controlled with an MS3X ECU, or any ECU with a 5V spark output, as it has a built in Ignitor.
The coils come with a 250mm long (8mm) HT lead, meaning they can be mounted on the head, rocker cover, wing, etc, of an older or modern engine.
Image shows a bank on my RV8 running sequential fuel and ignition using an ExtraEFI MS3X ECU
Idea where the Pencil Type COP's can't be used as they don't fit.
Supplied with the connector for the power / control, so everything you need.
Logic level 5V signal to fire unit. 5V starts charging the coil, drop to zero volts and the coil fires.
For wiring info see HERE.
No modifications needed, it plugs into your db9 pin connector on the front of the MS ECU, giving the RS-232 port a bluetooth wireless capability.
Fully configured ready for you to use the various app's on your Android phone or Android tablet to tune the ECU and to show dashboard info, etc.
Suitable for any MS ECU except for the early V2.2 boards or those with a micro USB port. If you have a V2.2 then you will need to add a couple of wires internally to give the bluetooth unit a 5V supply.
The MS1 has a different baud rate to the MS2 / MS3, so if you want to use it on an MS1 or another baud rate please Email me before buying and I will sort that for you.
These are included with an ExtraEFI ECU, so you do NOT need to order one if you buy an ECU from ExtraEFI.
But if you need a wiring loom for your MegaSquirt, then these are supplied with bare ended wires ready for you to wire to your setups connectors.
The looms are approx 1 meter long with a high quality, screened cable for the trigger signal and multiple 0.5mm ground cables for good noise separation.
Each wire is colour coded and has a label with it's description on it that matches the ExtraEFI diagrams.
As the wiring looms are made to your setup requirements, please contact me with all your details before ordering.
If your engine doesn't have both temperature sensors then it is possible to use a sensor from a scrap yard. But some people like to use the original MegaSquirt sensors as these are the sensors that are used as default in your MegaSquirt ECU - GM
The open style air sensor is ideal for fast changing temperatures from boosted engines. The closed style is ideal for coolant and air temperature sensing in most NA setups.
The thread is 3/8" NPT.
Each sensor is supplied with the connector ready to be crimped / soldered to your loom
Adds 2 Injector drivers, cam input, BlueTooth comms, Inputs / Outputs to an MS2
For more info see HERE.
This is the standard injector plug used on most vehicles using Bosch style injectors as found on Fords, RV8's, etc.
Each item comes with a rubber boot and 2 crimp terminals for the cables, for best results are to solder the wire to the crimps after crimping.
Wheels are lazer cut 3mm thick, 12.7mm diameter hole in the center and 8 radial aligning slots.
The Rover / TVR wheels are specially made to fit the various versions of pulleys that have been
fitted to the RV8's over the years. To ensure we supply the correct wheel / bracket, we require
a picture of your pulley. So please email me
This is ideal for wiring the power to the fuel pump, idle valve, injectors, ignition, etc, so that your ECU controls powers them up with the fuel pump.
This means wiring it into the fuel pump output, see here for a diagram. With 30A of control, it can feed most items that the ECU controls.